Trane XC95m, XR95, XV95, S9X2, S9V2, S9X1, XL80, XV80, XR80 Furnace Price & Reviews 2026

Trane is a very reputable brand of furnace that is associated with quality and efficiency, however, it is also a high-priced brand.

The cost of furnaces to American homeowners is between approximately 4,800 dollars on entry level models and 13,500 dollars on the high end models when installation is factored in.

We examine below some of the most important Trane gas furnace models, the XC95m, the XR95, the XV95, the S9X2, the S9V2, the S9X1, the XL80, the XV80 and the XR80, describing their efficiency, performance features, average retail and installed costs, and expert and user reviews.

Every section gives an objective, brief summary that will assist you in comparing these models.

Model	Efficiency (AFUE)	Key Features	Unit Price	Installed Price
Trane XC95m	97.3%	Modulating, variable-speed blower, ComfortLink™ II	$3,500–$4,500	$8,500–$13,500
Trane XV95	Up to 96.7%	Two-stage heating, variable-speed blower, ENERGY STAR®	$2,500–$3,500	$3,500–$6,000
Trane XR95	95%	Single-stage, durable design	Low $2,000s	$3,200–$4,500
Trane S9X2	96%	Two-stage, high-efficiency ECM blower	$2,500–$3,500	$3,500–$11,400
Trane S9V2	96% (up to 97% for VS)	Two-stage, variable-speed blower, premium features	~$3,000 (unit cost)	$8,500–$13,500
Trane S9X1	96%	Single-stage, efficient ECM blower	Low-to-mid $2,000s	$7,200–$11,400
Trane XL80	80%	Two-stage, legacy model	N/A	$3,000–$5,000
Trane XV80	80%	Two-stage, variable-speed blower	N/A	$3,200–$3,800
Trane XR80	80%	Single-stage, basic design	N/A	$2,900–$4,500

Trane XC95m Furnace

The Trane XC95m is Trane top-of-the-line modulating furnace, with up to 97.3 percent AFUE efficiency, the highest in the Trane line. It has a fully modulating gas valve and a variable speed blower motor that constantly adjusts itself to keep your home at the desired temperature within a fraction of a degree.

It is also a Trane model with the ComfortLink II communicating technology to calibrate and control the system more advancedly, which makes it an ultra-smart furnace that maximizes its performance when used with the compatible thermostats and AC units.

With these features, the XC95m provides very uniform heating and better air circulation in the house. HVAC professionals refer to XC95m as the most advanced comfort technology of Trane, offering the greatest control and comfort achievable in a gas furnace.

In practice, owners have reported that this furnace warms the house fast: one user review reported that it warmed their house much faster than their previous furnace, but it is a bit noisy when it starts up (a common characteristic of high-powered modulating furnaces). The general consensus is that the XC95m is very warm and very efficient and any slight noise during start up is more than compensated by the fuel savings and comfort advantages.

Price: The XC95m is a flagship model and therefore, it comes at a premium. The furnace itself usually sells in the middle-to-high end (usually between $3,500 and $4,500 in the unit) and the professional installation can add up to about $8,500 to $13,500 in most instances.

Installation prices are location and home size dependent; one dealer in the Midwest estimated approximately $5,900 6,600 installed on an XC95m in a 2,000 3,000 sq ft home. Although the initial cost of this model is very high, the ultra-high efficiency can reduce heating bills and can be eligible to energy tax credits or rebates which can cover some of the cost. It is a furnace that targets homeowners who desire the best performance and are ready to spend on long term comfort.

Trane XV95 Furnace

The Trane XV95 is a high efficiency two-stage furnace that was a high-end product of Trane in the 95% AFUE category. The XV95 has a very high AFUE of up to 96.7 percent and has two-stage heating (high and low fire) that enables it to operate more frequently on the lower setting to achieve better comfort and consistency.

It also has a variable-speed blower motor that is fitted with Trane Comfort-R technology to improve humidity control during cooling season. The two-stage gas heat and the variable airflow combination provides the XV95 with more even temperatures and quieter operation than single-stage furnaces. It is worth noting that the XV95 is an ENERGY STAR 9 certified product, which implies that it passed the rigorous efficiency tests, and can save a lot of money on energy bills compared to an older furnace.

When it was available in the market, experts considered Trane XV95 a balanced furnace of high-level quality. It was packed with a lot of the advanced features of Trane and was well built with a heavy insulated cabinet and durable heat exchanger to reduce noise.

One expert review said, “The XV95 is a great choice in case you want to have a great fuel consumption and amazing features.” Homeowners who have converted to two-stage furnaces such as the XV95 often report that they feel much more comfortable, with one user saying that after using a variable-speed two-stage system, he or she would never use a single-speed system again. It is agreed that the XV95 was a significant improvement in comfort compared to the basic models such as the XR95 and the operating cost was only slightly higher as the XV95 is still 96 percent efficient.

Price: The XV95 is no longer produced (Trane now has a newer S9V2 furnace that has similar two-stage performance but with newer features), but can still be obtained through some dealers. The furnace itself at the time of availability was usually priced at around 2,500-3,500 dollars and average installed prices were between 3,500 and 6,000 dollars depending on capacity and installation difficulty.

One installer in the Chicago area quoted fully installed cost of about $4,400 to 7,200 on common sizes. These prices caused the XV95 to be a major investment, although most owners believed the increased comfort and efficiency was worth it. The XV95 was frequently worth its price to those replacing an older single-stage unit, as it tended to be more evenly heating, quieter, and to save energy over the long term.

Trane XR95 Furnace

The Trane XR95 is a high efficiency furnace that is meant to provide 95 percent AFUE performance at a lower cost in a single-stage unit. It was the most efficient one-stage furnace of its generation in Trane.

The XR95 is a single-stage gas valve, so it operates at full capacity whenever it is called upon to heat, and that makes the design and controls less complex (and less expensive) than the two-stage XV95. The XR95 has a high fuel efficiency of 95 percent even though it does not have multi-stage modulation, which implies that it burns most of its fuel to produce usable heat. It also has quality parts that make it reliable like a long lasting silicon nitride hot surface igniter and an insulated blower compartment that makes it quiet. Trane supported this model with a strong warranty (lifetime on the heat exchanger and 10-year on parts) which indicates the belief in its durability.

The XR95 is reliable in terms of performance and has been referred to as a very durable and long-lasting furnace. A professional analysis observed that the XR95 lacks the most recent features or technology, but it is highly efficient and exceedingly durable, which makes it an excellent choice of homeowners who are not concerned about bells and whistles, but rather solid construction.

Most HVAC specialists believe that all Trane furnaces are reliable when installed correctly, and the XR95 is not an exception, with one technician saying that there is not much difference in core reliability between models such as the XR95 and XV95 other than their comfort levels. The people who purchased the XR95 were generally homeowners who wanted to achieve 95 percent efficiency at a reduced price and most of them are satisfied with the heating capabilities and energy savings of the product. The trade-off is that being a single-stage unit it can tolerate a little greater temperature fluctuations and can be a bit noisier at full blast than two-stage units.

Price: The XR95 was also discontinued (replaced by newer 96% models such as the S9X1), although it is still a widely used unit in many households and occasionally can be found as old stock. It was attractive in that it was affordable in terms of high efficiency.

Furnaces alone could cost as little as the low $2,000s and the fully installed systems were usually quoted in the range of $3,200 to $4,500 including installation on an average sized house. In Canada, an installed price of $3,500 to 4,665 was cited as average. These prices were much cheaper than that of the XV95, which was a more complex two-stage model. The XR95 was a sweet spot of efficiency, reliability and affordability to homeowners who wanted to reduce heating bills with a 95 AFUE furnace, but did not need the very best comfort features.

Trane S9X2 Furnace

The Trane S9X2 is a modern furnace of the Trane brand that has a high efficiency (96% AFUE) and a two-stage heating capacity. The S9X2 is one of the newer S-Series of Trane that is aimed at providing performance and price balance to homeowners.

It has a two-stage gas valve, which implies that it can operate on a low heat setting on the majority of heating occasions and increase to full strength on extremely cold days. This makes the indoor temperatures more consistent and efficient than a single-stage furnace. The S9X2 is also equipped with a high-efficiency ECM blower motor to provide enhanced airflow and efficiency but it is not a communicating unit (it does not use the ComfortLink II system, which is available only on Trane communicating models). It is small and soundless with an insulated 34-inch cabinet.

Trane sells the S9X2 as an excellent step-up model to people who desire near-premium efficiency at a price that is not the highest. It has a 96 percent AFUE and a two-stage operation, which makes it an outstanding furnace in terms of heating and can save a lot of fuel compared to an old furnace.

According to HVAC specialists, the S9X2 is a good choice in the middle-sized homes or those who are replacing a unit that is less efficient. It has everything but the modulating feature and communicating controls of Trane absolute best models, but to many families, two-stage heat is more than enough to be comfortable. The S9X2 has been a fast selling model because of the combination of efficiency, comfort and value.

Price: Being a mid- to high-end furnace, the S9X2 is priced accordingly to its two-stage system and high efficiency. The unit is sold at retail prices in the middle range (approximately between 2,500 and 3,500 dollars, depending on size). With professional installation included, prices may be estimated: local dealers are quoting about $3,500 – 5,000 installed on the S9X2, which is quite competitive as a 96% furnace.

On a national scale, the average installed cost is however higher at around 7,200 to 11,400 dollars depending on your area and the specifics of the job, on this model. This broad spread is because of the variation in labor rates, any necessary upgrades (such as new venting or duct modifications) and local pricing policies. On the whole, the S9X2 is likely to be a cheaper option than the modulating S9V2 or XC95m, but with almost top-tier efficiency, which is why it is suggested as a replacement to discontinued models such as the XV95.

Trane S9V2 Furnace

The Trane S9V2 is a high-efficiency furnace in Trane S-Series, which is similar to S9X2 but has some improved features. The S9V2 has the letter V in it, which means a variable-speed blower motor, and this is a two-stage furnace with a high-efficiency ECM blower that is able to vary its speed more dynamically.

It has an AFUE of up to about 96 percent (and Trane also sells a version of this model called the S9V2-VS that has an AFUE of up to 97 percent with a modulating gas valve). The two-stage burner of the S9V2 enables it to operate at low most of the time and high fire whenever necessary, which gives it very even heating. The variable-speed fan also enhances comfort by increasing or decreasing air volume gradually, and this prevents the short bursts of air and assists in the more even distribution of heat around the house. This furnace is also completely insulated and made to operate quietly, in fact, professionals mention that the S9V2-VS operates with such low noise levels that you will hardly realize that it is turned on due to its superior motor and cabinet design.

The S9V2 is basically a non-communicating version of Trane top XC95m. S9V2 (and S9V2-VS in particular) is regarded as one of the most efficient and comfortable models of Trane that is not communicating.

It is perfect for homeowners who desire the highest level of heating performance, very high efficiency, great humidity control and quiet, consistent heat without the need to have the ComfortLink II communication capabilities. HVAC experts usually suggest the S9V2 to customers who want the best comfort but cannot afford or do not want the very best model. When it comes to the satisfaction in the real world, the owners of S9V2 furnaces often commend the even heat and the fact that the unit operates in a whisper-quiet mode. It is also durable; the heavy duty heat exchanger and parts of Trane make it last up to 15-20 years or even more with regular maintenance.

Price: The S9V2 is a high-end model, and therefore its price is on the upper end of the Trane scale (though it is usually a little less than the XC95m because it is not a communicating furnace). In a standard installation, you may find quotes in the range of $4,000 to $6,000 installed of the S9V2-VS version, particularly in markets that have competition that keeps prices down.

But industry-wide surveys estimate the average installed cost to be about $8,500 to 13,500 (S9V2 (and S9V2-VS)) when it is all said and done. The retail (equipment-only) cost of the unit can be approximately 3,000 dollars (more or less depending on the BTU output). The high cost of installation is indicative of the fact that high-efficiency furnace installations are complex (condensate drains, PVC venting, etc.) and the equipment is premium. Concisely, the S9V2 will cost you a lot of money in the short term, but it will pay you back in the long term with reduced operating costs and comfort levels that are in the same range as the best furnaces available.

Trane S9X1 Furnace

The Trane S9X1 is a high efficiency furnace (96% AFUE) and is the entry level furnace in the Trane S-Series high efficiency product line. It is basically the contemporary substitute of the earlier single-stage 90+ percent models such as the XR95.

The S9X1 has single-stage heating (it is either on full blast or off) and a high-efficiency ECM blower motor in a fixed-speed design. It is Energy Star compliant with 96% AFUE, and it is a single-stage furnace that offers good efficiency, making it a good choice to homeowners who want to save a lot on energy bills but do not want to pay the premium price of a two-stage or modulating furnace. Physically, the design resembles the S9X2, except that it is easier to operate. It is a non-communicating furnace and its footprint is smaller due to only one heat output.

In performance, the S9X1 will warm equally well as the S9X2 in raw output, but since it cannot adjust the level of heating, it can cycle on and off more often. This may cause a little more fluctuation in the indoor temperature and a little more noise during start and stop, than its two-stage siblings.

Nevertheless, a large number of homeowners who have been using an older furnace will still consider the S9X1 a significant improvement in terms of efficiency as well as uniformity of heating (due to its more efficient heat exchanger and blower technology). It is usually advised to people in warmer climates or with smaller houses where the extra comfort of two-stage heating may not be worth the extra expense. Trane has stuck to its standards in terms of build, with stainless steel primary heat exchanger, secondary condensing heat exchanger, and a well-insulated cabinet, the S9X1 is durable and reasonably quiet. The S9X1 is basically a high-efficiency workhorse with a solid reputation that is value-oriented and concentrates on the basics.

Price: The S9X1 is usually the least expensive 96 percent AFUE furnace in the Trane line. The average installed cost of this model is approximately between 7,200 to 11,400 dollars, which is a few thousand dollars less than the two-stage S9X2 on average (based on promotions and local prices).

The common sizes of furnace-only retail price are typically in the low-to-mid $2,000s. The S9X1 saves homeowners on up front costs, both equipment and installation, compared to S9X2 or S9V2. As an example, the two-stage gas valve and variable-speed motor are more complex and thus cost-saving by omitting them. When a high-efficiency furnace is required (maybe to qualify for a rebate or to minimize the venting issues of an 80 percent furnace), the S9X1 is usually the furnace of choice when cost is a major factor. You just need to remember that it is less expensive but it does not offer the incremental comfort control of the two-stage models of Trane. This trade-off is acceptable to many since it saves a lot of money. To conclude, the S9X1 is a more affordable product with 96 percent efficiency, which makes high efficiency more affordable.

Trane XL80 Furnace

Trane XL80 is an older model of Trane standard-efficiency (80 percent AFUE) furnaces. It is a two-stage, 80% AFUE furnace, and at that efficiency level, this was a step up in technology over the basic single-stage models.

Most of the heating requirements are done on low stage and the XL80 can boost to the second stage when it is colder. It also has a four speed blower motor (not fully variable, but several taps to select different speeds) to control the airflow better than a single-speed fan. When it was produced, the XL80 offered homeowners an opportunity to obtain better comfort (due to two-stage heating) without upgrading to the more expensive condensing (90%+) furnace. The main characteristics were a heavy steel insulated cabinet, multi-port in-shot burners to provide consistent flames and a robust Adaptive Hot Surface Igniter to provide reliable starts. All this made XL80 have a reputation of being a solidly built and good performing vehicle in its category.

The XL80 was between the entry-level XR80 and the high-end XV80 in comparison to its siblings. In practice, this implied that the XL80 had the advantages of two-stage heat (more even temperatures, less frequent cycling) of the XV80, but generally not the fully variable-speed blower and some of the more advanced comfort features of the XV80.

It was a well-liked model during many years and can be met in millions of homes. The XL80 is usually a good compromise between comfort and cost to homeowners who have it: you get quieter, more consistent heat than you would with a single-stage furnace, but the system is simpler and usually less expensive to maintain than a high-efficiency furnace. The 80 percent AFUE of the XL80 implies that it exhausts through a standard flue (chimney or sidewall metal vent) and approximately 20 percent of the heat is wasted in the exhaust. An 80 percent unit such as the XL80 is a good idea in mild climates or where upgrading to a condensing furnace is not feasible. Although Trane has since gone to the S8 series to replace the XR80/XL80 models, the design heritage of the XL80 continues in those newer models with two-stage 80% operation as well.

Price: The XL80 is an older model, and is no longer sold new, but was initially sold as a more cost-effective method of obtaining two-stage heating. A similar two-stage 80 percent furnace installation in modern terms would cost something in the range of 3,000 to 5,000 dollars all in, depending on local labor rates and any other work that may be required.

When it was offered, the XL80 fully installed price was usually in the middle between the basic XR80 and the high-end XV80. Since we have observed the XR80 to be installed at an average price of about 3500-3900 and the XV80 at about 3200-3800 (according to one dealer), the XL80 was typically in the middle 3000s in most homes. This made it a good mid-level choice. Although you probably are not going to purchase a new XL80 today, it can be helpful to know its price and placement in case you are comparing an existing XL80 in your house to newer replacements, such as replacing an XL80 with a current Trane two-stage (such as the S8X2 80% furnace) will provide you with similar performance but you will pay a little more because of inflation and new technology.

Trane XV80 Furnace

The Trane XV80 was the high-end furnace of Trane with 80 percent AFUE, but with a lot of high-end features in a standard efficiency furnace. It is a variable-speed blower two-stage furnace, which implies that it can easily regulate the airflow and the amount of heat produced to enhance comfort.

At an efficiency of up to 80 percent AFUE, it is not a fuel-saving furnace as a high-efficiency 90 percent+ furnace, but the XV80 is designed to provide the best comfort at its efficiency rating. The two heating stages give longer, more gentle heating cycles on mild days and full capacity heating on colder days. In the meantime, the variable-speed ECM fan motor operates at the minimum required speed to achieve even temperatures and can increase or decrease its speed over time – this does not only make the XV80 run quieter but also assists in improved air distribution and humidity control. The furnace is designed with an insulated cabinet to reduce noise, a heavy-duty steel heat exchanger to be durable, and it is compatible with the advanced controls of Trane (it is not a communicating model). It also has the Comfort-R 1 mode of increased dehumidification when combined with a Trane AC.

Being the high-end 80 percent model, the XV80 was characterized by its outstanding comfort and low-noise operation among standard efficiency furnaces. It basically provided you with a lot of the experience of a top-end furnace (uniform heat, low sound level, and advanced airflow management) without the PVC venting and increased price of a condensing furnace.

Numerous HVAC professionals and consumers praised the XV80 as providing the comfort and quiet performance of a high-end furnace at a price that is not as high as a 90+ furnace. It was an excellent compromise between the people who could not install a condensing furnace (because of venting limitations) and those who did not feel the need of >95% efficiency in their climate, yet wanted the most comfort features. Trane no longer makes the XV80, but it is still a standard by which 80 percent furnaces are measured in terms of performance.

Price: The XV80 was a well priced 80 percent furnace with all its advanced features. In one case, a local HVAC contractor quoted the Trane XV80 as being between 3,200 and 3,800 dollars installed in their region.

This was inclusive of the furnace and a professional installation that had all the materials required. Such a price put the XV80 just a bit higher than the single-stage models (which is logical, the main cost adders are the variable-speed motor and two-stage controls). A new XV80 (when it was available) would cost nationwide, on average, between approximately 3,000 and 5,000 installed, as did the XL80.

Today, when you want to replace an XV80, you would be considering an S9X2 or maybe an S8V2 (80% two-stage) – those newer units may be a bit more costly because of efficiency improvements. However, when we look at the period of the XV80 alone, it was a luxury comfort at a reasonable premium. Most owners believed it was a good investment, because it provided a significantly better comfort compared to base models, yet fuel prices remained unchanged.

Trane XR80 Furnace

The Trane XR80 was an 80 percent AFUE gas furnace that was the lowest point of Trane standard efficiency line. It is a single-stage furnace, which implies that it will be at full heat output when it is on.

The XR80 has a fixed-speed blower motor and a simple design of reliability and cost-effective warmth. Having an AFUE of up to 80%, it complies with the minimum efficiency requirement of contemporary furnaces (i.e., 20 percent of heat energy is wasted up the flue). The XR80 might not have the advanced features of other products but it is simple and cheaper to buy.

It is constructed using the standard quality parts of Trane, a heavy duty heat exchanger, multi-port burners to ensure uniform ignition and an insulated cabinet to reduce noise. The footprint is comparable with other Trane furnaces, and it may sometimes be able to fit in the same space that an older 80 percent furnace was installed, using existing venting.

Those who opt to purchase the XR80 are homeowners who are on a budget or whose heating needs are simple. This furnace will be dependable in heating a house and maintaining it comfortable, but without the more precise temperature control of two-stage furnaces.

In case your house does not have uneven temperatures or serious airflow problems, a single-stage furnace such as the XR80 can be a convenient solution. It offers constant, albeit rather primitive, heat production. The XR80 is a workhorse to many users, it kicks on when it is needed and runs without much ado year after year. A single advantage of the simple single-stage system is that there are fewer parts that can go wrong; some homeowners and technicians like that the XR80 has fewer parts to go wrong and may be easier to service.

The negative is that when it is on, it is on full blast so you may feel the more intense bursts of warm air and the furnace may run more often. The noise levels are normally more than the two-stage Trane furnaces, just because the blower and burner are always at 100 percent when they are on. However, Trane engineering ensures that it is not too noisy in its category, and the XR80 is known to be very durable.

Price: The XR80 was the least expensive furnace available at the time of Trane and it is still an economical choice when it comes to used or existing furnaces. In a new installation, the cost was about $3,520 to $3,960 installed on average home.

Practically, homeowners could have been quoted anywhere between approximately 2,900 dollars (in low cost areas or smaller capacity furnaces) to approximately 4,500 dollars (in larger furnaces or higher cost urban areas). The price was low because of the simplicity of the unit, the equipment was less expensive and the installation was also less expensive than the more efficient furnaces. In fact, even now, the least costly path in terms of initial cost is usually to replace an old furnace with a simple 80 percent model such as the XR80 equivalent.

It should be mentioned that in certain areas, current building codes promote or mandate more efficient units, and so the XR80 (or its more modern 80% descendant, the S8B1/S8X1) is most prevalent in southern climates or where it is difficult to vent a 90% furnace. In case cost was the motivating factor, the XR80 was a solid furnace at a steal. All you need to do is to keep in mind that you will be saving money in the short-term but an 80 percent furnace will consume more fuel in the long-term than a 90 percent+ furnace. However, the XR80 was the better option in terms of price and heating requirements of many people since the purchase and installation cost of the XR80 was significantly lower.

How to Get the Best Trane Furnace Prices?

• To begin with, remember that the quality of installation is the most significant thing in furnace project. Never compromise contractor quality with a cheaper price.
• Second, do not forget to check the latest tax credit and rebates.
• Third, request at least 3 bids prior to making the decision. To get 3 free estimates of your local contractors, you can click here, this estimate already considers rebates and tax credit and automatically filters unqualified contractors.

Finally, after you selected the appropriate contractor, do not forget to apply the strategies of this guide: homeowners tactics when negotiating with HVAC dealer to obtain the final best price.